[edit interfaces ge-0/0/0 unit 0 family inet address set vrrp-group 1 virtual-address 10.1.1.1 [edit interfaces ge-0/0/0 unit 0 family inet address set vrrp-group 1Īt this point, we will configure VRRP parameters. We can use any number between 0-255 as VRRP group. Now, let’s configure VRRP group, which helps to run multiple VRRP. So, let’s use power of “ edit” command here 🙂 edit interfaces ge-0/0/0 unit 0 family inet address 10.1.1.2/24 At Juniper, the VRRP configuration syntax is after the IP address. However, let’s move to the main configuration part–Īccording our plan, we will do VRRP configuration on Ge-0/0/0 interface. Set routing-options static route 0.0.0.0/0 next-hop 2.2.2.1 Set routing-options static route 0.0.0.0/0 next-hop show | display set | match routing Routing: show | display set | match routing
Set interfaces ge-0/0/0 unit 0 family inet address 10.1.1.3/24 Set interfaces ge-0/0/1 unit 0 family inet address 2.2.2.2/30
Set interfaces ge-0/0/0 unit 0 family inet address show | display set | match interface Set interfaces ge-0/0/1 unit 0 family inet address 1.1.1.2/30 It can be seen that for 10.10.10.3 the MAC address learnt is not the virtual MAC of reth (which is 00:10:db:ff:10:00), but MAC address of fe-0/0/5 interface of 100-3.Interface: show | display set | match interface Total sessions: run show arp no-resolve | match 10.10.10.3Ģ8:c0:da:e1:50:85 10.10.10.3 fe-0/0/5.0 none The ICMP sessions are the ip-monitoring ping packets sent by the cluster causing 100-1 to learn the MAC address of 10.10.10.3 as secondary node's interface. Session ID: 12567, Policy name: self-traffic-policy/1, Timeout: 2, Valid Session ID: 12566, Policy name: self-traffic-policy/1, Timeout: 2, Valid Also the MAC addresses of child interface of reth0 (fe-0/0/5 from each node) are as run show interfaces fe-0/0/5 extensive | match hardwareĬurrent address: 00:10:db:ff:10:00, Hardware address: run show interfaces fe-0/0/5 extensive | match hardwareĬurrent address: 00:10:db:ff:10:00, Hardware address: 28:c0:da:e1:50:85Ĭhecking the ICMP sessions and arp entries on the upstream SRX 100-1 run show security flow session protocol icmp Interface reth0.0 secondary-ip-address 10.10.10.3 įrom this it can be seen that there is a proxy-arp configured for 10.10.10.3, but that IP address is also being used as secondary-ip-address in ip-monitoring. On SRX cluster we have the following show chassis cluster redundancy-group 1 ip-monitoring Since this IP-address will be used by the secondary-node to send ICMP probes, the upstream device learns the MAC of secondary node's child interface.įor example consider the following topology: This IP will be used as the source to send pings from secondary node for ip-monitoring. This happens when IP-monitoring is configured and the IP-address is being used for which proxy-arp is configured as a secondary-ip-address in the IP-monitoring configuration. Neighbor device is learning MAC address of secondary node's child interface for the IP address on reth interface thumbsupĠ Article ID: KB27275 KB Last Updated: Version: 1.0 Summary:
Search our Knowledge Base sites to find answers to your questions. We apologize for any inconvenience this may cause.Įxpected Duration: 3 days, 21 hours Support Downloads Knowledge Base Juniper Support Portal Community Knowledge Base
#Juniper srx show mac address on interface free#
A complete listing of local toll free numbers are available at Contact Support. Should you have any issues during this time, you can open a case in the Juniper Support Portal, or call us toll free at 1-88. Problem Report (PR) Search - Starting Friday April 1st, 5pm PDT.
During this time, some of our Self-Service systems and tools will be unavailable. On Thursday, March 31st, 2022, from 5pm PDT to Sunday, April 3rd, 2pm PDT, we will be conducting upgrades on our systems to better support you.
0 kommentar(er)
